GE Appliances delivers high-efficiency ductless mini-split systems combining inverter technology, built-in WiFi, and whisper-quiet operation for precise room-by-room comfort. From single-zone wall mounts to multi-zone cassette systems, GE Appliances ductless solutions provide flexible, energy-efficient heating and cooling without ductwork.What's Included: 1G12CB1BEA Outdoor Unit: The GE Appliances Caliber Series outdoor unit delivers 20 SEER2 cooling. Features A-PAM DC Inverter technology for precise capacity modulation and quiet operation, Blue Fin anti-corrosion coating for long-lasting durability, and on-demand defrost. R-410A refrigerant. 10-year parts and compressor warranty when registered with licensed install. GS12WB1BEA Indoor Unit: The GE Appliances Caliber 115V 12K BTU indoor unit delivers whisper-quiet, draft-free conditioned air. Insta-Position auto-swing louvers (up for cooling, down for heating), Quiet Mode, Turbo Mode, and Warm Start (no cold drafts on heat startup). Built-in air filter included. Includes licensed and insured installation by professionals, along with the Ductless Install Kit for a complete setup.Professional Installation Removal & haul-off of existing equipment Installation of new equipment and all included parts Refrigerant line connection, evacuation & charge to OEM spec Full system start-up, airflow check & operational testing Permit pulled and permit fees paid with the local jurisdiction Final inspection and job-site clean-up Performed by a licensed, insured HVAC contractor Ductless Mini-Split Installation Kit Refrigerant line set copper line set (liquid + suction), insulated Electrical dedicated circuit breaker or disconnect, whip connections Mounting hardware wall bracket or cassette plate, weather seal Condensate drainage drain hose and fittings from indoor unit Communication wire signal/control cable between ODU and IDU Not Included The following items are not included unless listed on your written invoice: Electrical panel upgrades or new circuit breakers beyond the dedicated circuit Structural wall reinforcement or special mounting substrates Refrigerant line set extension beyond standard run lengths Condensate pump when gravity drain is not feasible Crane or rooftop rigging for difficult equipment access Carpentry, drywall, paint, or flooring repair after installation If any of the above are needed, our technician will assess on-site and provide a written change-order quote. Nothing extra is charged without your written approval.5-Year Labor WarrantyLabor is covered for 5 years from the date of installation. If a covered defect related to our installation causes a failure, we return at no charge for diagnosis and labor. Parts replacements are handled under the OEM parts warranty (10 years when registered). Excludes maintenance, filter changes, customer-caused damage, and acts of nature. Full terms on the Warranty & Guarantee page. Capacity (BTU) 12K BTU Tonnage 1-Ton Cooling Efficiency (SEER2) 20 Heat Capacity @ 5°F N/A Outdoor Unit Model 1G12CB1BEA Indoor Unit Model GS12WB1BEA Mount Type Wall Mount Refrigerant R-410A Voltage 115V Liquid Line 1/4" Suction Line 3/8" AHRI N/A Warranty 10 Year Parts (When Registered with OEM) RESOURCES Outdoor Unit Indoor Unit SPEC SHEET SPEC SHEET INSTALLATION MANUAL INSTALLATION MANUAL Outdoor Unit Indoor Unit LIMITED WARRANTY LIMITED WARRANTY

Read more less

GE Appliances is a trusted leader in home comfort, delivering high-performance HVAC systems that combine efficiency, reliability, and innovation. Focused on energy savings and durability, GE Appliances products meet top residential heating and cooling standards. Whether upgrading or installing new, GE Appliances provides advanced solutions to keep your home comfortable year-round.What's Included: NS16A Condenser: The GE Appliances NS16A is a single-stage central air conditioner delivering 13.8 SEER2 cooling efficiency. Features a durable tube-and-fin coil for reliable heat exchange, optimized airflow design for consistent performance, and on-demand defrost protection. Uses low-GWP R-454B refrigerant. 10-year parts and compressor limited warranty when registered. NAM60E1TA5S Fan Coil: The GE Appliances NAM is a fan coil air handler providing efficient indoor heat exchange when paired with a GE Appliances air conditioner condenser. Factory-installed TXV and R-454B compatibility ensure reliable, long-lasting cooling performance. GE Appliances AUX Electric Heat Kit (Model 8122772): Electric resistance heat element for supplemental heating capability. Includes licensed and insured HVAC installation by professionals, along with the Install Kit for a complete setup.Professional Installation Removal & haul-off of existing equipment Installation of new equipment and all included parts Refrigerant line connection, evacuation & charge to OEM spec Full system start-up, airflow check & operational testing Permit pulled and permit fees paid with the local jurisdiction Final inspection and job-site clean-up Performed by a licensed, insured HVAC contractor Condenser & Coil Kit Electrical & mounting disconnect, A/C whip, condenser pad Refrigerant line filter drier, locking caps, ArmaFlex insulation Not Included This listing covers the equipment and standard installation scope above. The following items are not included unless specifically listed on your written invoice or estimate: Electrical panel upgrades or new breakers beyond the standard disconnect Ductwork modifications, repairs, replacement, or new runs New refrigerant line set (existing line set is reused when in good condition) Condenser pad re-pour, raised platform, or hurricane tie-downs (standard composite pad is included) Condenser relocation to a new exterior position Gas line extension, re-routing, or new gas line installation Crane or rooftop rigging for difficult equipment access Condensate drain line rework beyond the immediate connection at the unit Thermostat upgrades (standard thermostat reuse only) Asbestos abatement, mold remediation, or hazardous material handling Carpentry, drywall, paint, or flooring repair after installation If any of the above are needed for your home, our technician will assess on-site and provide a written change-order quote before any additional work begins. Nothing extra is charged or performed without your written approval.5-Year Labor WarrantyLabor is covered for 5 years from the date of installation. If a covered defect related to our installation causes a failure, we return at no charge for diagnosis and labor. Parts replacements are handled under the OEM parts warranty (10 years when registered). Excludes maintenance, filter changes, customer-caused damage, and acts of nature. Full terms on the Warranty & Guarantee page. Bundle Size/Tonnage 5-Ton Bundle Cooling Efficiency (SEER2) 13.8 Condenser Model NS16A60SA5 Condenser Stages Single Fan Coil Model NAM60E1TA5S Coil Type Fan Coil AUX Heat Kit Model 8122772 Heat Source Cooling Only AUX Heat Source Electric Refrigerant R-454B Warranty 10 Year Parts, 10 Year Compressor(When Registered with OEM) RESOURCES Condenser Fan Coil TECHNICAL RESOURCES TECHNICAL RESOURCES Condenser Fan Coil LIMITED WARRANTY LIMITED WARRANTY

Read more less

GE Appliances is a trusted leader in home comfort, delivering high-performance HVAC systems that combine efficiency, reliability, and innovation. Focused on energy savings and durability, GE Appliances products meet top residential heating and cooling standards. Whether upgrading or installing new, GE Appliances provides advanced solutions to keep your home comfortable year-round.What's Included: NS16A Condenser: The GE Appliances NS16A is a single-stage central air conditioner delivering 14.7 SEER2 cooling efficiency. Features a durable tube-and-fin coil for reliable heat exchange, optimized airflow design for consistent performance, and on-demand defrost protection. Uses low-GWP R-454B refrigerant. 10-year parts and compressor limited warranty when registered. NAM48E1TA5S Fan Coil: The GE Appliances NAM is a fan coil air handler providing efficient indoor heat exchange when paired with a GE Appliances air conditioner condenser. Factory-installed TXV and R-454B compatibility ensure reliable, long-lasting cooling performance. GE Appliances AUX Electric Heat Kit (Model 812277): Electric resistance heat element for supplemental heating capability. Includes licensed and insured HVAC installation by professionals, along with the Install Kit for a complete setup.Professional Installation Removal & haul-off of existing equipment Installation of new equipment and all included parts Refrigerant line connection, evacuation & charge to OEM spec Full system start-up, airflow check & operational testing Permit pulled and permit fees paid with the local jurisdiction Final inspection and job-site clean-up Performed by a licensed, insured HVAC contractor Condenser & Coil Kit Electrical & mounting disconnect, A/C whip, condenser pad Refrigerant line filter drier, locking caps, ArmaFlex insulation Not Included This listing covers the equipment and standard installation scope above. The following items are not included unless specifically listed on your written invoice or estimate: Electrical panel upgrades or new breakers beyond the standard disconnect Ductwork modifications, repairs, replacement, or new runs New refrigerant line set (existing line set is reused when in good condition) Condenser pad re-pour, raised platform, or hurricane tie-downs (standard composite pad is included) Condenser relocation to a new exterior position Gas line extension, re-routing, or new gas line installation Crane or rooftop rigging for difficult equipment access Condensate drain line rework beyond the immediate connection at the unit Thermostat upgrades (standard thermostat reuse only) Asbestos abatement, mold remediation, or hazardous material handling Carpentry, drywall, paint, or flooring repair after installation If any of the above are needed for your home, our technician will assess on-site and provide a written change-order quote before any additional work begins. Nothing extra is charged or performed without your written approval.5-Year Labor WarrantyLabor is covered for 5 years from the date of installation. If a covered defect related to our installation causes a failure, we return at no charge for diagnosis and labor. Parts replacements are handled under the OEM parts warranty (10 years when registered). Excludes maintenance, filter changes, customer-caused damage, and acts of nature. Full terms on the Warranty & Guarantee page. Bundle Size/Tonnage 4-Ton Bundle Cooling Efficiency (SEER2) 14.7 Condenser Model NS16A48SA5 Condenser Stages Single Fan Coil Model NAM48E1TA5S Coil Type Fan Coil AUX Heat Kit Model 812277 Heat Source Cooling Only AUX Heat Source Electric Refrigerant R-454B Warranty 10 Year Parts, 10 Year Compressor(When Registered with OEM) RESOURCES Condenser Fan Coil TECHNICAL RESOURCES TECHNICAL RESOURCES Condenser Fan Coil LIMITED WARRANTY LIMITED WARRANTY

Read more less

GE Appliances is a trusted leader in home comfort, delivering high-performance HVAC systems that combine efficiency, reliability, and innovation. Focused on energy savings and durability, GE Appliances products meet top residential heating and cooling standards. Whether upgrading or installing new, GE Appliances provides advanced solutions to keep your home comfortable year-round.What's Included: NS16A Condenser: The GE Appliances NS16A is a single-stage central air conditioner delivering 14.7 SEER2 cooling efficiency. Features a durable tube-and-fin coil for reliable heat exchange, optimized airflow design for consistent performance, and on-demand defrost protection. Uses low-GWP R-454B refrigerant. 10-year parts and compressor limited warranty when registered. NAM42P1TA5S Fan Coil: The GE Appliances NAM is a fan coil air handler providing efficient indoor heat exchange when paired with a GE Appliances air conditioner condenser. Factory-installed TXV and R-454B compatibility ensure reliable, long-lasting cooling performance. GE Appliances AUX Electric Heat Kit (Model 812277): Electric resistance heat element for supplemental heating capability. Includes licensed and insured HVAC installation by professionals, along with the Install Kit for a complete setup.Professional Installation Removal & haul-off of existing equipment Installation of new equipment and all included parts Refrigerant line connection, evacuation & charge to OEM spec Full system start-up, airflow check & operational testing Permit pulled and permit fees paid with the local jurisdiction Final inspection and job-site clean-up Performed by a licensed, insured HVAC contractor Condenser & Coil Kit Electrical & mounting disconnect, A/C whip, condenser pad Refrigerant line filter drier, locking caps, ArmaFlex insulation Not Included This listing covers the equipment and standard installation scope above. The following items are not included unless specifically listed on your written invoice or estimate: Electrical panel upgrades or new breakers beyond the standard disconnect Ductwork modifications, repairs, replacement, or new runs New refrigerant line set (existing line set is reused when in good condition) Condenser pad re-pour, raised platform, or hurricane tie-downs (standard composite pad is included) Condenser relocation to a new exterior position Gas line extension, re-routing, or new gas line installation Crane or rooftop rigging for difficult equipment access Condensate drain line rework beyond the immediate connection at the unit Thermostat upgrades (standard thermostat reuse only) Asbestos abatement, mold remediation, or hazardous material handling Carpentry, drywall, paint, or flooring repair after installation If any of the above are needed for your home, our technician will assess on-site and provide a written change-order quote before any additional work begins. Nothing extra is charged or performed without your written approval.5-Year Labor WarrantyLabor is covered for 5 years from the date of installation. If a covered defect related to our installation causes a failure, we return at no charge for diagnosis and labor. Parts replacements are handled under the OEM parts warranty (10 years when registered). Excludes maintenance, filter changes, customer-caused damage, and acts of nature. Full terms on the Warranty & Guarantee page. Bundle Size/Tonnage 3.5-Ton Bundle Cooling Efficiency (SEER2) 14.7 Condenser Model NS16A42SA5 Condenser Stages Single Fan Coil Model NAM42P1TA5S Coil Type Fan Coil AUX Heat Kit Model 812277 Heat Source Cooling Only AUX Heat Source Electric Refrigerant R-454B Warranty 10 Year Parts, 10 Year Compressor(When Registered with OEM) RESOURCES Condenser Fan Coil TECHNICAL RESOURCES TECHNICAL RESOURCES Condenser Fan Coil LIMITED WARRANTY LIMITED WARRANTY

Read more less

GE Appliances is a trusted leader in home comfort, delivering high-performance HVAC systems that combine efficiency, reliability, and innovation. Focused on energy savings and durability, GE Appliances products meet top residential heating and cooling standards. Whether upgrading or installing new, GE Appliances provides advanced solutions to keep your home comfortable year-round.What's Included: NS16A Condenser: The GE Appliances NS16A is a single-stage central air conditioner delivering 15.2 SEER2 cooling efficiency. Features a durable tube-and-fin coil for reliable heat exchange, optimized airflow design for consistent performance, and on-demand defrost protection. Uses low-GWP R-454B refrigerant. 10-year parts and compressor limited warranty when registered. NAM36P1TA5S Fan Coil: The GE Appliances NAM is a fan coil air handler providing efficient indoor heat exchange when paired with a GE Appliances air conditioner condenser. Factory-installed TXV and R-454B compatibility ensure reliable, long-lasting cooling performance. GE Appliances AUX Electric Heat Kit (Model 8122768): Electric resistance heat element for supplemental heating capability. Includes licensed and insured HVAC installation by professionals, along with the Install Kit for a complete setup.Professional Installation Removal & haul-off of existing equipment Installation of new equipment and all included parts Refrigerant line connection, evacuation & charge to OEM spec Full system start-up, airflow check & operational testing Permit pulled and permit fees paid with the local jurisdiction Final inspection and job-site clean-up Performed by a licensed, insured HVAC contractor Condenser & Coil Kit Electrical & mounting disconnect, A/C whip, condenser pad Refrigerant line filter drier, locking caps, ArmaFlex insulation Not Included This listing covers the equipment and standard installation scope above. The following items are not included unless specifically listed on your written invoice or estimate: Electrical panel upgrades or new breakers beyond the standard disconnect Ductwork modifications, repairs, replacement, or new runs New refrigerant line set (existing line set is reused when in good condition) Condenser pad re-pour, raised platform, or hurricane tie-downs (standard composite pad is included) Condenser relocation to a new exterior position Gas line extension, re-routing, or new gas line installation Crane or rooftop rigging for difficult equipment access Condensate drain line rework beyond the immediate connection at the unit Thermostat upgrades (standard thermostat reuse only) Asbestos abatement, mold remediation, or hazardous material handling Carpentry, drywall, paint, or flooring repair after installation If any of the above are needed for your home, our technician will assess on-site and provide a written change-order quote before any additional work begins. Nothing extra is charged or performed without your written approval.5-Year Labor WarrantyLabor is covered for 5 years from the date of installation. If a covered defect related to our installation causes a failure, we return at no charge for diagnosis and labor. Parts replacements are handled under the OEM parts warranty (10 years when registered). Excludes maintenance, filter changes, customer-caused damage, and acts of nature. Full terms on the Warranty & Guarantee page. Bundle Size/Tonnage 3-Ton Bundle Cooling Efficiency (SEER2) 15.2 Condenser Model NS16A36SA5 Condenser Stages Single Fan Coil Model NAM36P1TA5S Coil Type Fan Coil AUX Heat Kit Model 8122768 Heat Source Cooling Only AUX Heat Source Electric Refrigerant R-454B Warranty 10 Year Parts, 10 Year Compressor(When Registered with OEM) RESOURCES Condenser Fan Coil TECHNICAL RESOURCES TECHNICAL RESOURCES Condenser Fan Coil LIMITED WARRANTY LIMITED WARRANTY

Read more less

GE Appliances is a trusted leader in home comfort, delivering high-performance HVAC systems that combine efficiency, reliability, and innovation. Focused on energy savings and durability, GE Appliances products meet top residential heating and cooling standards. Whether upgrading or installing new, GE Appliances provides advanced solutions to keep your home comfortable year-round.What's Included: NS16A Condenser: The GE Appliances NS16A is a single-stage central air conditioner delivering 14.7 SEER2 cooling efficiency. Features a durable tube-and-fin coil for reliable heat exchange, optimized airflow design for consistent performance, and on-demand defrost protection. Uses low-GWP R-454B refrigerant. 10-year parts and compressor limited warranty when registered. NAM30P1TA5S Fan Coil: The GE Appliances NAM is a fan coil air handler providing efficient indoor heat exchange when paired with a GE Appliances air conditioner condenser. Factory-installed TXV and R-454B compatibility ensure reliable, long-lasting cooling performance. GE Appliances AUX Electric Heat Kit (Model 8122768): Electric resistance heat element for supplemental heating capability. Includes licensed and insured HVAC installation by professionals, along with the Install Kit for a complete setup.Professional Installation Removal & haul-off of existing equipment Installation of new equipment and all included parts Refrigerant line connection, evacuation & charge to OEM spec Full system start-up, airflow check & operational testing Permit pulled and permit fees paid with the local jurisdiction Final inspection and job-site clean-up Performed by a licensed, insured HVAC contractor Condenser & Coil Kit Electrical & mounting disconnect, A/C whip, condenser pad Refrigerant line filter drier, locking caps, ArmaFlex insulation Not Included This listing covers the equipment and standard installation scope above. The following items are not included unless specifically listed on your written invoice or estimate: Electrical panel upgrades or new breakers beyond the standard disconnect Ductwork modifications, repairs, replacement, or new runs New refrigerant line set (existing line set is reused when in good condition) Condenser pad re-pour, raised platform, or hurricane tie-downs (standard composite pad is included) Condenser relocation to a new exterior position Gas line extension, re-routing, or new gas line installation Crane or rooftop rigging for difficult equipment access Condensate drain line rework beyond the immediate connection at the unit Thermostat upgrades (standard thermostat reuse only) Asbestos abatement, mold remediation, or hazardous material handling Carpentry, drywall, paint, or flooring repair after installation If any of the above are needed for your home, our technician will assess on-site and provide a written change-order quote before any additional work begins. Nothing extra is charged or performed without your written approval.5-Year Labor WarrantyLabor is covered for 5 years from the date of installation. If a covered defect related to our installation causes a failure, we return at no charge for diagnosis and labor. Parts replacements are handled under the OEM parts warranty (10 years when registered). Excludes maintenance, filter changes, customer-caused damage, and acts of nature. Full terms on the Warranty & Guarantee page. Bundle Size/Tonnage 2.5-Ton Bundle Cooling Efficiency (SEER2) 14.7 Condenser Model NS16A30SA5 Condenser Stages Single Fan Coil Model NAM30P1TA5S Coil Type Fan Coil AUX Heat Kit Model 8122768 Heat Source Cooling Only AUX Heat Source Electric Refrigerant R-454B Warranty 10 Year Parts, 10 Year Compressor(When Registered with OEM) RESOURCES Condenser Fan Coil TECHNICAL RESOURCES TECHNICAL RESOURCES Condenser Fan Coil LIMITED WARRANTY LIMITED WARRANTY

Read more less

GE Appliances is a trusted leader in home comfort, delivering high-performance HVAC systems that combine efficiency, reliability, and innovation. Focused on energy savings and durability, GE Appliances products meet top residential heating and cooling standards. Whether upgrading or installing new, GE Appliances provides advanced solutions to keep your home comfortable year-round.What's Included: NS16A Condenser: The GE Appliances NS16A is a single-stage central air conditioner delivering 15.5 SEER2 cooling efficiency. Features a durable tube-and-fin coil for reliable heat exchange, optimized airflow design for consistent performance, and on-demand defrost protection. Uses low-GWP R-454B refrigerant. 10-year parts and compressor limited warranty when registered. NAM24P1TA5S Fan Coil: The GE Appliances NAM is a fan coil air handler providing efficient indoor heat exchange when paired with a GE Appliances air conditioner condenser. Factory-installed TXV and R-454B compatibility ensure reliable, long-lasting cooling performance. GE Appliances AUX Electric Heat Kit (Model 8122766): Electric resistance heat element for supplemental heating capability. Includes licensed and insured HVAC installation by professionals, along with the Install Kit for a complete setup.Professional Installation Removal & haul-off of existing equipment Installation of new equipment and all included parts Refrigerant line connection, evacuation & charge to OEM spec Full system start-up, airflow check & operational testing Permit pulled and permit fees paid with the local jurisdiction Final inspection and job-site clean-up Performed by a licensed, insured HVAC contractor Condenser & Coil Kit Electrical & mounting disconnect, A/C whip, condenser pad Refrigerant line filter drier, locking caps, ArmaFlex insulation Not Included This listing covers the equipment and standard installation scope above. The following items are not included unless specifically listed on your written invoice or estimate: Electrical panel upgrades or new breakers beyond the standard disconnect Ductwork modifications, repairs, replacement, or new runs New refrigerant line set (existing line set is reused when in good condition) Condenser pad re-pour, raised platform, or hurricane tie-downs (standard composite pad is included) Condenser relocation to a new exterior position Gas line extension, re-routing, or new gas line installation Crane or rooftop rigging for difficult equipment access Condensate drain line rework beyond the immediate connection at the unit Thermostat upgrades (standard thermostat reuse only) Asbestos abatement, mold remediation, or hazardous material handling Carpentry, drywall, paint, or flooring repair after installation If any of the above are needed for your home, our technician will assess on-site and provide a written change-order quote before any additional work begins. Nothing extra is charged or performed without your written approval.5-Year Labor WarrantyLabor is covered for 5 years from the date of installation. If a covered defect related to our installation causes a failure, we return at no charge for diagnosis and labor. Parts replacements are handled under the OEM parts warranty (10 years when registered). Excludes maintenance, filter changes, customer-caused damage, and acts of nature. Full terms on the Warranty & Guarantee page. Bundle Size/Tonnage 2-Ton Bundle Cooling Efficiency (SEER2) 15.5 Condenser Model NS16A24SA5 Condenser Stages Single Fan Coil Model NAM24P1TA5S Coil Type Fan Coil AUX Heat Kit Model 8122766 Heat Source Cooling Only AUX Heat Source Electric Refrigerant R-454B Warranty 10 Year Parts, 10 Year Compressor(When Registered with OEM) RESOURCES Condenser Fan Coil TECHNICAL RESOURCES TECHNICAL RESOURCES Condenser Fan Coil LIMITED WARRANTY LIMITED WARRANTY

Read more less

GE Appliances is a trusted leader in home comfort, delivering high-performance HVAC systems that combine efficiency, reliability, and innovation. Focused on energy savings and durability, GE Appliances products meet top residential heating and cooling standards. Whether upgrading or installing new, GE Appliances provides advanced solutions to keep your home comfortable year-round.What's Included: NS16A Condenser: The GE Appliances NS16A is a single-stage central air conditioner delivering 15.5 SEER2 cooling efficiency. Features a durable tube-and-fin coil for reliable heat exchange, optimized airflow design for consistent performance, and on-demand defrost protection. Uses low-GWP R-454B refrigerant. 10-year parts and compressor limited warranty when registered. NAM18P1TA5S Fan Coil: The GE Appliances NAM is a fan coil air handler providing efficient indoor heat exchange when paired with a GE Appliances air conditioner condenser. Factory-installed TXV and R-454B compatibility ensure reliable, long-lasting cooling performance. GE Appliances AUX Electric Heat Kit (Model 8122766): Electric resistance heat element for supplemental heating capability. Includes licensed and insured HVAC installation by professionals, along with the Install Kit for a complete setup.Professional Installation Removal & haul-off of existing equipment Installation of new equipment and all included parts Refrigerant line connection, evacuation & charge to OEM spec Full system start-up, airflow check & operational testing Permit pulled and permit fees paid with the local jurisdiction Final inspection and job-site clean-up Performed by a licensed, insured HVAC contractor Condenser & Coil Kit Electrical & mounting disconnect, A/C whip, condenser pad Refrigerant line filter drier, locking caps, ArmaFlex insulation Not Included This listing covers the equipment and standard installation scope above. The following items are not included unless specifically listed on your written invoice or estimate: Electrical panel upgrades or new breakers beyond the standard disconnect Ductwork modifications, repairs, replacement, or new runs New refrigerant line set (existing line set is reused when in good condition) Condenser pad re-pour, raised platform, or hurricane tie-downs (standard composite pad is included) Condenser relocation to a new exterior position Gas line extension, re-routing, or new gas line installation Crane or rooftop rigging for difficult equipment access Condensate drain line rework beyond the immediate connection at the unit Thermostat upgrades (standard thermostat reuse only) Asbestos abatement, mold remediation, or hazardous material handling Carpentry, drywall, paint, or flooring repair after installation If any of the above are needed for your home, our technician will assess on-site and provide a written change-order quote before any additional work begins. Nothing extra is charged or performed without your written approval.5-Year Labor WarrantyLabor is covered for 5 years from the date of installation. If a covered defect related to our installation causes a failure, we return at no charge for diagnosis and labor. Parts replacements are handled under the OEM parts warranty (10 years when registered). Excludes maintenance, filter changes, customer-caused damage, and acts of nature. Full terms on the Warranty & Guarantee page. Bundle Size/Tonnage 1.5-Ton Bundle Cooling Efficiency (SEER2) 15.5 Condenser Model NS16A18SA5 Condenser Stages Single Fan Coil Model NAM18P1TA5S Coil Type Fan Coil AUX Heat Kit Model 8122766 Heat Source Cooling Only AUX Heat Source Electric Refrigerant R-454B Warranty 10 Year Parts, 10 Year Compressor(When Registered with OEM) RESOURCES Condenser Fan Coil TECHNICAL RESOURCES TECHNICAL RESOURCES Condenser Fan Coil LIMITED WARRANTY LIMITED WARRANTY

Read more less

GE Appliances is a trusted leader in home comfort, delivering high-performance HVAC systems that combine efficiency, reliability, and innovation. Focused on energy savings and durability, GE Appliances products meet top residential heating and cooling standards. Whether upgrading or installing new, GE Appliances provides advanced solutions to keep your home comfortable year-round.What's Included: NS18H60HA5 Connect Series Heat Pump: The GE Appliances NS18H Connect Series is a variable-speed inverter heat pump with a compact side-discharge cabinet (17-1/8" depth) delivering 16.8 SEER2 cooling. Rated for heating down to -22°F ENERGY STAR® certified cold-climate performance. Dual fuel-rated, compatible with 600+ AHRI systems, as low as 54 dB. Built-in SmartHQ WiFi (Alexa & Google). Eligible for federal 25C tax credits. R-454B low-GWP refrigerant. 5-year base / 10-year registered warranty. NAM60V1TA5S Variable-Speed Air Handler: The GE Appliances NAM Variable-Speed air handler features an ECM variable-speed blower motor for precise airflow control, enhanced dehumidification, and quiet operation. Factory-installed TXV and R-454B compatibility ensure efficient performance when paired with GE heat pumps. 8122772 Electric Heat Kit: The 8122772 electric heat strip kit installs inside the air handler to provide supplemental electric heating during cold weather, available in multiple kW outputs (5/7.5/10/15 kW) to meet your home's heating requirements. Required for heat pump operation in heating mode. Includes licensed and insured HVAC installation by professionals, along with the Install Kit for a complete setup.Professional Installation Removal & haul-off of existing equipment Installation of new equipment and all included parts Refrigerant line connection, evacuation & charge to OEM spec Full system start-up, airflow check & operational testing Permit pulled and permit fees paid with the local jurisdiction Final inspection and job-site clean-up Performed by a licensed, insured HVAC contractor Heat Pump System Kit Electrical & mounting disconnect, A/C whip, condenser pad Refrigerant line (outdoor) filter drier, locking caps, ArmaFlex insulation Refrigerant line (indoor) bi-flow filter drier, ArmaFlex insulation Drainage & safety secondary drain pan, float switch, P-trap PVC fittings couplings, elbows, adapters for condensate line Not Included This listing covers the equipment and standard installation scope above. The following items are not included unless specifically listed on your written invoice or estimate: Electrical panel upgrades or new breakers beyond the standard disconnect Ductwork modifications, repairs, replacement, or new runs New refrigerant line set (existing line set is reused when in good condition) Condenser pad re-pour, raised platform, or hurricane tie-downs (standard composite pad is included) Condenser relocation to a new exterior position Gas line extension, re-routing, or new gas line installation Crane or rooftop rigging for difficult equipment access Condensate drain line rework beyond the immediate connection at the unit Thermostat upgrades (standard thermostat reuse only) Asbestos abatement, mold remediation, or hazardous material handling Carpentry, drywall, paint, or flooring repair after installation If any of the above are needed for your home, our technician will assess on-site and provide a written change-order quote before any additional work begins. Nothing extra is charged or performed without your written approval.5-Year Labor WarrantyLabor is covered for 5 years from the date of installation. If a covered defect related to our installation causes a failure, we return at no charge for diagnosis and labor. Parts replacements are handled under the OEM parts warranty (10 years when registered). Excludes maintenance, filter changes, customer-caused damage, and acts of nature. Full terms on the Warranty & Guarantee page. Bundle Size/Tonnage 5-Ton Bundle Cooling Efficiency (SEER2) 16.8 Bundle Heating Efficiency (HSPF2) 9 Heat Pump Model NS18H60HA5 Heat Pump Stages Variable Speed Inverter Air Handler Model NAM60V1TA5S Air Handler Blower Variable Air Handler Capacity 55k Heat Kit Model 8122772 Heat Kit Output 5/7.5/10/15 kW Heat Source Electric Heat Pump AHRI 216604759 Refrigerant R-454B Warranty 10 Year Parts, 10 Year Compressor(When Registered with OEM) RESOURCES Heat Pump Air Handler Heat Kit TECHNICAL RESOURCES TECHNICAL RESOURCES TECHNICAL RESOURCES Heat Pump Air Handler Heat Kit LIMITED WARRANTY LIMITED WARRANTY LIMITED WARRANTY

Read more less

GE Appliances is a trusted leader in home comfort, delivering high-performance HVAC systems that combine efficiency, reliability, and innovation. Focused on energy savings and durability, GE Appliances products meet top residential heating and cooling standards. Whether upgrading or installing new, GE Appliances provides advanced solutions to keep your home comfortable year-round.What's Included: NS18H60HA5 Connect Series Heat Pump: The GE Appliances NS18H Connect Series is a variable-speed inverter heat pump with a compact side-discharge cabinet (17-1/8" depth) delivering 18 SEER2 cooling. Rated for heating down to -22°F ENERGY STAR® certified cold-climate performance. Dual fuel-rated, compatible with 600+ AHRI systems, as low as 54 dB. Built-in SmartHQ WiFi (Alexa & Google). Eligible for federal 25C tax credits. R-454B low-GWP refrigerant. 5-year base / 10-year registered warranty. NAM48V1TA5S Variable-Speed Air Handler: The GE Appliances NAM Variable-Speed air handler features an ECM variable-speed blower motor for precise airflow control, enhanced dehumidification, and quiet operation. Factory-installed TXV and R-454B compatibility ensure efficient performance when paired with GE heat pumps. 812277 Electric Heat Kit: The 812277 electric heat strip kit installs inside the air handler to provide supplemental electric heating during cold weather, available in multiple kW outputs (5/7.5/10/15 kW) to meet your home's heating requirements. Required for heat pump operation in heating mode. Includes licensed and insured HVAC installation by professionals, along with the Install Kit for a complete setup.Professional Installation Removal & haul-off of existing equipment Installation of new equipment and all included parts Refrigerant line connection, evacuation & charge to OEM spec Full system start-up, airflow check & operational testing Permit pulled and permit fees paid with the local jurisdiction Final inspection and job-site clean-up Performed by a licensed, insured HVAC contractor Heat Pump System Kit Electrical & mounting disconnect, A/C whip, condenser pad Refrigerant line (outdoor) filter drier, locking caps, ArmaFlex insulation Refrigerant line (indoor) bi-flow filter drier, ArmaFlex insulation Drainage & safety secondary drain pan, float switch, P-trap PVC fittings couplings, elbows, adapters for condensate line Not Included This listing covers the equipment and standard installation scope above. The following items are not included unless specifically listed on your written invoice or estimate: Electrical panel upgrades or new breakers beyond the standard disconnect Ductwork modifications, repairs, replacement, or new runs New refrigerant line set (existing line set is reused when in good condition) Condenser pad re-pour, raised platform, or hurricane tie-downs (standard composite pad is included) Condenser relocation to a new exterior position Gas line extension, re-routing, or new gas line installation Crane or rooftop rigging for difficult equipment access Condensate drain line rework beyond the immediate connection at the unit Thermostat upgrades (standard thermostat reuse only) Asbestos abatement, mold remediation, or hazardous material handling Carpentry, drywall, paint, or flooring repair after installation If any of the above are needed for your home, our technician will assess on-site and provide a written change-order quote before any additional work begins. Nothing extra is charged or performed without your written approval.5-Year Labor WarrantyLabor is covered for 5 years from the date of installation. If a covered defect related to our installation causes a failure, we return at no charge for diagnosis and labor. Parts replacements are handled under the OEM parts warranty (10 years when registered). Excludes maintenance, filter changes, customer-caused damage, and acts of nature. Full terms on the Warranty & Guarantee page. Bundle Size/Tonnage 4-Ton Bundle Cooling Efficiency (SEER2) 18 Bundle Heating Efficiency (HSPF2) 9.5 Heat Pump Model NS18H60HA5 Heat Pump Stages Variable Speed Inverter Air Handler Model NAM48V1TA5S Air Handler Blower Variable Air Handler Capacity 47.5k Heat Kit Model 812277 Heat Kit Output 5/7.5/10/15 kW Heat Source Electric Heat Pump AHRI 215869483 Refrigerant R-454B Warranty 10 Year Parts, 10 Year Compressor(When Registered with OEM) RESOURCES Heat Pump Air Handler Heat Kit TECHNICAL RESOURCES TECHNICAL RESOURCES TECHNICAL RESOURCES Heat Pump Air Handler Heat Kit LIMITED WARRANTY LIMITED WARRANTY LIMITED WARRANTY

Read more less

GE Appliances is a trusted leader in home comfort, delivering high-performance HVAC systems that combine efficiency, reliability, and innovation. Focused on energy savings and durability, GE Appliances products meet top residential heating and cooling standards. Whether upgrading or installing new, GE Appliances provides advanced solutions to keep your home comfortable year-round.What's Included: NS18H36HA5 Connect Series Heat Pump: The GE Appliances NS18H Connect Series is a variable-speed inverter heat pump with a compact side-discharge cabinet (17-1/8" depth) delivering 18 SEER2 cooling. Rated for heating down to -22°F ENERGY STAR® certified cold-climate performance. Dual fuel-rated, compatible with 600+ AHRI systems, as low as 54 dB. Built-in SmartHQ WiFi (Alexa & Google). Eligible for federal 25C tax credits. R-454B low-GWP refrigerant. 5-year base / 10-year registered warranty. NAM36V1TA5S Variable-Speed Air Handler: The GE Appliances NAM Variable-Speed air handler features an ECM variable-speed blower motor for precise airflow control, enhanced dehumidification, and quiet operation. Factory-installed TXV and R-454B compatibility ensure efficient performance when paired with GE heat pumps. 8122768 Electric Heat Kit: The 8122768 electric heat strip kit installs inside the air handler to provide supplemental electric heating during cold weather, available in multiple kW outputs (5/7.5/10/15 kW) to meet your home's heating requirements. Required for heat pump operation in heating mode. Includes licensed and insured HVAC installation by professionals, along with the Install Kit for a complete setup.Professional Installation Removal & haul-off of existing equipment Installation of new equipment and all included parts Refrigerant line connection, evacuation & charge to OEM spec Full system start-up, airflow check & operational testing Permit pulled and permit fees paid with the local jurisdiction Final inspection and job-site clean-up Performed by a licensed, insured HVAC contractor Heat Pump System Kit Electrical & mounting disconnect, A/C whip, condenser pad Refrigerant line (outdoor) filter drier, locking caps, ArmaFlex insulation Refrigerant line (indoor) bi-flow filter drier, ArmaFlex insulation Drainage & safety secondary drain pan, float switch, P-trap PVC fittings couplings, elbows, adapters for condensate line Not Included This listing covers the equipment and standard installation scope above. The following items are not included unless specifically listed on your written invoice or estimate: Electrical panel upgrades or new breakers beyond the standard disconnect Ductwork modifications, repairs, replacement, or new runs New refrigerant line set (existing line set is reused when in good condition) Condenser pad re-pour, raised platform, or hurricane tie-downs (standard composite pad is included) Condenser relocation to a new exterior position Gas line extension, re-routing, or new gas line installation Crane or rooftop rigging for difficult equipment access Condensate drain line rework beyond the immediate connection at the unit Thermostat upgrades (standard thermostat reuse only) Asbestos abatement, mold remediation, or hazardous material handling Carpentry, drywall, paint, or flooring repair after installation If any of the above are needed for your home, our technician will assess on-site and provide a written change-order quote before any additional work begins. Nothing extra is charged or performed without your written approval.5-Year Labor WarrantyLabor is covered for 5 years from the date of installation. If a covered defect related to our installation causes a failure, we return at no charge for diagnosis and labor. Parts replacements are handled under the OEM parts warranty (10 years when registered). Excludes maintenance, filter changes, customer-caused damage, and acts of nature. Full terms on the Warranty & Guarantee page. Bundle Size/Tonnage 3-Ton Bundle Cooling Efficiency (SEER2) 18 Bundle Heating Efficiency (HSPF2) 9.5 Heat Pump Model NS18H36HA5 Heat Pump Stages Variable Speed Inverter Air Handler Model NAM36V1TA5S Air Handler Blower Variable Air Handler Capacity 36k Heat Kit Model 8122768 Heat Kit Output 5/7.5/10/15 kW Heat Source Electric Heat Pump AHRI 215869481 Refrigerant R-454B Warranty 10 Year Parts, 10 Year Compressor(When Registered with OEM) RESOURCES Heat Pump Air Handler Heat Kit TECHNICAL RESOURCES TECHNICAL RESOURCES TECHNICAL RESOURCES Heat Pump Air Handler Heat Kit LIMITED WARRANTY LIMITED WARRANTY LIMITED WARRANTY

Read more less

GE Appliances is a trusted leader in home comfort, delivering high-performance HVAC systems that combine efficiency, reliability, and innovation. Focused on energy savings and durability, GE Appliances products meet top residential heating and cooling standards. Whether upgrading or installing new, GE Appliances provides advanced solutions to keep your home comfortable year-round.What's Included: NS18H24HA5 Connect Series Heat Pump: The GE Appliances NS18H Connect Series is a variable-speed inverter heat pump with a compact side-discharge cabinet (17-1/8" depth) delivering 18 SEER2 cooling. Rated for heating down to -22°F ENERGY STAR® certified cold-climate performance. Dual fuel-rated, compatible with 600+ AHRI systems, as low as 54 dB. Built-in SmartHQ WiFi (Alexa & Google). Eligible for federal 25C tax credits. R-454B low-GWP refrigerant. 5-year base / 10-year registered warranty. NAM24V1TA5S Variable-Speed Air Handler: The GE Appliances NAM Variable-Speed air handler features an ECM variable-speed blower motor for precise airflow control, enhanced dehumidification, and quiet operation. Factory-installed TXV and R-454B compatibility ensure efficient performance when paired with GE heat pumps. 8122766 Electric Heat Kit: The 8122766 electric heat strip kit installs inside the air handler to provide supplemental electric heating during cold weather, available in multiple kW outputs (5/7.5/10/15 kW) to meet your home's heating requirements. Required for heat pump operation in heating mode. Includes licensed and insured HVAC installation by professionals, along with the Install Kit for a complete setup.Professional Installation Removal & haul-off of existing equipment Installation of new equipment and all included parts Refrigerant line connection, evacuation & charge to OEM spec Full system start-up, airflow check & operational testing Permit pulled and permit fees paid with the local jurisdiction Final inspection and job-site clean-up Performed by a licensed, insured HVAC contractor Heat Pump System Kit Electrical & mounting disconnect, A/C whip, condenser pad Refrigerant line (outdoor) filter drier, locking caps, ArmaFlex insulation Refrigerant line (indoor) bi-flow filter drier, ArmaFlex insulation Drainage & safety secondary drain pan, float switch, P-trap PVC fittings couplings, elbows, adapters for condensate line Not Included This listing covers the equipment and standard installation scope above. The following items are not included unless specifically listed on your written invoice or estimate: Electrical panel upgrades or new breakers beyond the standard disconnect Ductwork modifications, repairs, replacement, or new runs New refrigerant line set (existing line set is reused when in good condition) Condenser pad re-pour, raised platform, or hurricane tie-downs (standard composite pad is included) Condenser relocation to a new exterior position Gas line extension, re-routing, or new gas line installation Crane or rooftop rigging for difficult equipment access Condensate drain line rework beyond the immediate connection at the unit Thermostat upgrades (standard thermostat reuse only) Asbestos abatement, mold remediation, or hazardous material handling Carpentry, drywall, paint, or flooring repair after installation If any of the above are needed for your home, our technician will assess on-site and provide a written change-order quote before any additional work begins. Nothing extra is charged or performed without your written approval.5-Year Labor WarrantyLabor is covered for 5 years from the date of installation. If a covered defect related to our installation causes a failure, we return at no charge for diagnosis and labor. Parts replacements are handled under the OEM parts warranty (10 years when registered). Excludes maintenance, filter changes, customer-caused damage, and acts of nature. Full terms on the Warranty & Guarantee page. Bundle Size/Tonnage 2-Ton Bundle Cooling Efficiency (SEER2) 18 Bundle Heating Efficiency (HSPF2) 10 Heat Pump Model NS18H24HA5 Heat Pump Stages Variable Speed Inverter Air Handler Model NAM24V1TA5S Air Handler Blower Variable Air Handler Capacity 24k Heat Kit Model 8122766 Heat Kit Output 5/7.5/10/15 kW Heat Source Electric Heat Pump AHRI 215869480 Refrigerant R-454B Warranty 10 Year Parts, 10 Year Compressor(When Registered with OEM) RESOURCES Heat Pump Air Handler Heat Kit TECHNICAL RESOURCES TECHNICAL RESOURCES TECHNICAL RESOURCES Heat Pump Air Handler Heat Kit LIMITED WARRANTY LIMITED WARRANTY LIMITED WARRANTY

Read more less